Active Ingredients
66.34% Ethanol
Citric Acid
L-Lactic Acid

Compatible Dispenser
2XL Wipe Dispenser

Contact Time
10 Minute

Dilution System
Yes

Directions/Instructions
Directions for Use Hard Surfaces<ul><li>Shake well.</li><li>Hold can upright 6-8 inches from the surface.</li><li>Spray surface until thoroughly wet. Surface will be disinfected after 5 minutes.</li></ul>Note: Heavy soil must be removed prior to disinfecting. A potable water rinse is required for food contact surfaces. Use as directed.Soft Surfaces<ul><li>Shake well.</li><li>Hold can upright 6-8 inches from the surface.</li><li>Using a smooth zig-zag motion, spray mist across fabric until wet, but do not saturate.</li><li>Air dry. Bacteria will be killed in 30 seconds.</li></ul>Note: For first-time use on soft surfaces, spot-test in a small, inconspicuous area. Use as directed.Air<ul><li>Close all doors, windows and air vents.</li><li>Shake well.</li><li>Hold can upright and spray toward center of room for 10 seconds. Odor-causing bacteria in the air will be killed instantly.</li><li>After spray has settled, resume normal air ventilation. Repeat as needed.</li></ul>Note: For maximum effectiveness, relative humidity should be between 45% and 70%. Use as directed. Use Sites <ul><li>Dental offices</li><li>Doctor offices</li><li>Hospitals</li><li>Long-term care facilities</li><li>Nursing homes</li><li>Patient areas</li><li>Waiting rooms</li></ul> Key Surfaces Hard Surfaces<ul><li>Bed pans</li><li>Carts</li><li>Doorknobs</li><li>Empty wastebaskets</li><li>Remote controls</li><li>Light switches</li><li>Telephone receivers</li><li>Walkers</li><li>Wheelchairs</li></ul>
For General Use: <ul> <li>For use on hard, nonporous inanimate environmental surfaces such as floors, walls, glazed porcelain, glazed ceramic tile, plastic surfaces, shower stalls, bathtubs and cabinets</li> <li>To disinfect inanimate, hard nonporous surfaces, dilute according to label directions.</li> <li>Apply solution with a mop, cloth, sponge or hand-pump trigger sprayer so as to wet all surfaces thoroughly.</li> <li>Allow to remain wet for 10 minutes then remove excess liquid.</li> <li>For heavily soiled areas, a pre-cleaning step is required. Prepare a fresh solution for each use.</li> </ul> For J-Fill® Use: <ul> <li>Insert cartridge into dispenser (see J-FILL® dispenser instructions for proper cartridge placement). Fill small bottle or bucket or use gun to apply a foam directly onto surfaces to be cleaned, scrubbing with a soft brush, pad or cloth. Do not allow foam to dry. Rinse surfaces thoroughly. NOTE: Some commercial strength cleaners are unsuitable for use on some surfaces. Test in an inconspicuous area prior to use.</li> </ul> For RTD® Use: <ul> <li>Fill trigger spray bottle with product. Apply to surfaces to be cleaned.</li> <li>Wipe with clean cloth or towel to dry. Dilute with cold water.</li> <li>To avoid food contamination after cleaning, sanitize and rinse all food contact surfaces with potable water before reuse.</li> </ul>
Use instructions <ul> <li>Virex® Plus is a one-step, quaternary-based disinfectant cleaner concentrate for use on hard, nonporous surfaces such as floors, walls, glazed porcelain, and plastic surfaces in hospitals, nursing homes, schools, hotels, public areas and other facilities where cleaning and prevention of cross-contamination are critical.</li> </ul> Preparation of Disinfectant Use-Solution <ul> <li>Mix ½ oz. per gallon of water (1:256). Use 1 oz. per gallon of water to kill Norovirus , Enterobacter aerogenes, and Serratia marcescens. Use 2 oz. per gallon of water to kill Adenovirus Type 5 and Type 7.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use-solution with a sprayer, thoroughly wetting surface.</li> <li>Let treated surface remain wet for contact time indicated on label or reference sheet.</li> <li>Wipe dry with a cloth, sponge, or mop, or allow to air dry.</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted</li> </ul> For Use as a Cleaner and Deodorizer <ul> <li>Apply use-solution using a sprayer.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul> For Use as a Non-Acid Toilet Bowl and Urinal Disinfectant/Cleaner <ul> <li>Empty toilet bowl or urinal and apply use-solution to exposed surfaces and under the rim with a sprayer.</li> <li>Brush or swab thoroughly, allow to stand for contact time indicated on the label and flush.</li> </ul> To Control Mold and Mildew <ul> <li>Follow disinfection instructions.</li> <li>Repeat treatment every seven days, or more often if new growth appears.</li> </ul> Dilutable Disinfectant Cleaner <ul> <li>1:256 dilution - Bactericidal, Virucidal, and Fungicidal, in 3 minutes. Kills HIV-1 and Influenza Type A in 1 minute. Some organisms require a 10 minute contact time and/or other dilutions. Please see product label or reference sheet for complete information.</li> <li>1:128 dilution - Kills Norovirus in 5 minutes.</li> </ul>
Directions for Use To Clean and Disinfect: Use on hard, nonporous surfaces. Spray surface until surface is thoroughly wet. Surface must remain visibly wet for 2 minutes. Then wipe. For visibly soiled areas, a precleaning is required. To Sanitize and Deodorize: Use on hard, nonporous non-food-contact surfaces. Preclean visibly soiled surfaces. Spray surface until thoroughly wet. Allow treated surface to remain visibly wet for 15 seconds. Allow to air dry or wipe dry. Use Sites <ul> <li>Schools</li> <li>Offices / Break rooms</li> <li>Day care centers</li> <li>Recreational centers</li> <li>Public facilities</li> </ul>
It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Preparation of use-solution: Add 5 oz. per gallon of water, to disinfect hard precleaned nonporous surfaces. Disinfection/*Virucidal Directions: Remove gross filth or heavy soil, then thoroughly clean surfaces. Apply use-solution to hard nonporous surfaces, thoroughly wetting surfaces with a cloth, mop, sponge or sprayer. For sprayer applications, use a coarse spray device. Spray 6 - 8 inches from surface, rub with brush, sponge or cloth. Avoid breathing spray. Treated surfaces must remain wet for 10 minutes. Wipe dry with a clean cloth or sponge or let air dry. Rinse all surfaces that come in contact with food such as countertops, appliances, tables and stovetops with potable water before reuse. Do not use on utensils, glassware or dishes. Prepare a fresh solution daily or more often if the use-solution becomes visibly diluted or soiled. This product is not for use on medical device surfaces. *KILLS HIV ON PRE-CLEANED ENVIRONMENTAL SURFACES/OBJECTS PREVIOUSLY SOILED WITH BLOOD/BODY FLUIDS in health care settings or other settings in which there is an expected likelihood of soiling of inanimate surfaces/objects with blood or body fluids, and in which the surfaces/objects likely to be soiled with blood or body fluids can be associated with the potential for transmission of Human Immunodeficiency Virus Type 1 (HIV-1) (associated with AIDS). SPECIAL INSTRUCTIONS FOR CLEANING AND DECONTAMINATION AGAINST HIV-1 ON SURFACES/OBJECTS SOILED WITH BLOOD/BODY FLUIDS. PERSONAL PROTECTION: Clean-up should always be done wearing protective latex gloves, gowns, masks, eye protection. CLEANING PROCEDURE: Blood and other body fluids containing HIV must be thoroughly cleaned from surfaces and objects before application of this product. CONTACT TIME: Leave surfaces wet for 1 minute (60 seconds). Use a 10 minute contact time for disinfection against all other viruses, bacteria and fungi claimed. DISPOSAL OF INFECTIOUS MATERIAL: Blood, body fluids, cleaning materials and clothing should be autoclaved and disposed of according to local regulations for infectious waste disposal. To Clean and Deodorize or to Preclean Prior to Disinfection: Depending on the soil level of the area to be cleaned, use 12 - 16 oz. of this product per gallon of water. Rub with brush, sponge or cloth. Wipe dry with a clean cloth or sponge or let air dry. For Mildew Control: Follow directions for Disinfection. Repeat treatment every seven days or when new growth appears. Deodorizing directions: Nursing Homes, Hospitals, Hotels, Schools: 2 - 4 oz. in chemical toilets, waste receptacles, bed pans, drainage bottles, diaper pails, hampers, disposals, commodes and air conditioner pans will eliminate odors.
Specs & Application Instructions: <ul> <li>Use where odors are a problem</li> <li>Can be used in hospitals, nursing homes, schools and colleges, offices, public areas and restrooms</li> <li>Use on hard, non-porous restroom surfaces: glazed ceramic tile, glazed porcelain, chrome, stainless steel and plastic surfaces associated with floors, walls, fixtures, toilets, urinals, sinks, shower rooms and locker rooms.</li> </ul>
TO KILL 99.9% of bacteria and viruses FOR 24 HOURS: To sanitize hard, non-porous, non-food contact surfaces for 24 hours: Apply product. Allow to air dry without wiping. Reapply if surface is scrubbed. To kill 99.9% of viruses for 24 hours: Preclean visibly soiled surfaces. Hold container 6"-8" from surface and spray until thoroughly wet. For use only on hard, nonporous nonfood contact surfaces. Allow to air dry without wiping. Reapply if surface is scrubbed. TO SANITIZE: Pre-clean heavily soiled surfaces. Hold container 6-8" from surface and spray until thoroughly wet. <ul> <li>To sanitize hard, non-porous, non-food contact surfaces: Apply product. Let stand 10 seconds. Wipe clean with a damp cloth.</li> <li>To sanitize hard, non-porous, non-food contact surfaces for 24 hours: Apply product. Allow to air dry without wiping. Reapply if surface is scrubbed.</li> </ul> *When used as directed, effective against Staphylococcus aureus & Enterobacter aerogenes. TO DISINFECT BACTERIA AND VIRUSES: <ul> <li>Pre-clean surface.</li> <li>Hold container 6-8" from surface and spray until thoroughly wet.</li> <li>For bacteria*, let stand for 60 seconds. Wipe with a cloth.</li> <li>For bacteria, viruses and fungi, let stand for 5 minutes. Wipe with a cloth.</li> <li>To kill the virus causes COVID-19, spray Microban 24 Multi-Purpose Cleaner on a hard, non-porous, non-food-contact surface and allow it to remain wet for 60 seconds. Let the surface air dry without wiping.</li> </ul> When used as directed, effective against bacteria Pseudomonas aeruginosa, Staphylococcus aureus, Salmonella enterica, Escherichia coli 0157:H7. When used as directed, effective against bacteria (Pseudomonas aeruginosa, Staphylococcus aureus, Salmonella enterica, Escherichia coli 0157:H7), viruses (Influenza A H1N1, Respiratory Syncytial Virus [RSV], Human Coronavirus, Herpes Simplex type 1, Herpes Simplex type 2 and Rotavirus), and fungi (Trichophyton mentagrophytes, and Aspergillus niger). TO DEODORIZE: Spray on surfaces as needed. TO PREVENT MOLD & MILDEW: ON HARD SURFACES*: <ul> <li>Pre-clean heavily soiled surfaces.</li> <li>Hold container 6-8" from the hard surface and spray until thoroughly wet.</li> <li>Allow to air dry.</li> <li>Repeat every 7 days to inhibit mold and mildew growth.</li> </ul> When used as directed, effective against Aspergillus niger. ON SOFT SURFACES*: <ul> <li>Pre-clean heavily soiled surfaces.</li> <li>Apply to fabric surface until wet (do not saturate).</li> <li>Allow to air dry.</li> <li>Repeat every 28 days to inhibit mold and mildew growth.</li> </ul>
To Sanitize and Disinfect: <ul> <li>Pre-clean surface.</li> <li>Hold can upright 6" to 8" from surface.</li> <li>Spray 3 to 4 seconds until covered with mist.</li> <li>To sanitize:</li> <li>Surfaces must remain wet for 10 seconds then allow to air dry.</li> <li>To disinfect:</li> <li>Surfaces must remain wet for 3 minutes then allow to air dry.</li> </ul> To Control and Prevent Mold and Mildew: <ul> <li>Apply to pre-cleaned surface</li> <li>Allow to remain wet for 3 minutes</li> <li>Let air dry</li> <li>Repeat applications in weekly intervals or when mold and mildew growth appears</li> </ul> Use on hard, non-porous surfaces <ul> <li>Pre-clean surfaces prior to use.</li> <li>Hold can upright 6 to 8 inches from surface.</li> <li>Spray 3 to 4 seconds until covered with mist.</li> <li>Rinse toys and food contact surfaces with potable water after use.</li> </ul> To disinfect: <ul> <li>Surfaces must remain wet for 3 minutes then allow to air dry.</li> <li>For Norovirus surfaces must remain wet for 10 minutes then allow to air dry</li> </ul> To sanitize: <ul> <li>Surfaces must remain wet for 10 seconds then allow to air dry.</li> </ul> To control and prevent mold and mildew: <ul> <li>Apply to pre-cleaned surface.</li> <li>Allow to remain wet for 3 minutes.</li> <li>Let air dry.</li> <li>Repeat applications in weekly intervals or when mold and mildew growth appears.</li> </ul> To deodorize: <ul> <li>Spray on surfaces as needed.</li> </ul> To spot sanitize soft surfaces: <ul> <li>Spray until fabric is wet.</li> <li>DO NOT SATURATE.</li> <li>Fabric must remain wet for 30 seconds.</li> <li>Let air dry.</li> <li>For difficult odors, repeat application.</li> </ul>
To unlock cap: Turn counterclockwise 2 clicks. Lock cap, after use. For use in air: Hold can upright. Spray towards the center of the room. To deodorize: Spray on surfaces as needed. To disinfect hard non-porous surfaces: Pre-clean surface. Spray until thoroughly wet. Leave for 5 minutes to disinfect. Air dry. Rinse toys and food contact surfaces with potable water after use. Do not use on polished wood, painted surfaces, or acrylic plastics.
To unlock cap: Turn counterclockwise 2 clicks. Lock cap, after use. For use in air: Hold can upright. Spray towards the center of the room. To deodorize: Spray on surfaces as needed. To disinfect hard non-porous surfaces: Pre-clean surface. Spray until thoroughly wet. Leave for 5 minutes to disinfect. Air dry. Rinse toys and food contact surfaces with potable water after use. Do not use on polished wood, painted surfaces, or acrylic plastics.
Usage Instructions It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Refill only with this product. Prime trigger by pumping before first use. Hold trigger 6-8" from surface. TO DISINFECT HARD, NONPOROUS SURFACES: Spray and leave visibly wet for 10 min. Food-contact surfaces must be rinsed with potable water. TO SPOT SANITIZE SOFT SURFACES**: Spray until surface is wet. Leave visibly wet for 5 min. Let air dry. **For use as a spot sanitizer on fabrics and textiles.
Use instructions<ul><li> Prior to application, thoroughly clean all surfaces to be treated to remove gross filth or heavy soil.</li></ul> Disinfectant<ul><li> Hold can upright and spray from a distance of 6 to 8 inches until area for treatment is thoroughly moistened. Allow to remain wet for 10 minutes. Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li></ul> Control of Mold and Mildew<ul><li> Spray surface until thoroughly moistened. Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li><li> Repeat application in 7 days.</li></ul> Control of Fungus<ul><li> Spray surface until thoroughly moistened.</li><li> Allow surfaces to remain wet for 10 minutes.</li><li> Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li></ul>
DIRECTIONS FOR USE: It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Before use in federally inspected meat and poultry food processing plants and dairies, food products and packaging materials must be removed from the room or carefully protected. DILUTION: [1:256] ½ oz. per gallon of water DISINFECTION/VIRUCIDAL*/FUNGICIDAL/MOLD AND MILDEW CONTROL DIRECTIONS: Apply use-solution to hard, nonporous surfaces, thoroughly wetting surfaces with a sprayer. Treated surfaces must remain wet for 3 minutes. For disinfection against Enterovirus. 5 minute contact time. For disinfection against Legionella pneumophilia, Staphylococcus aureus - Multi-Drug Resistant, and SARS Associated Coronavirus use 10 minute contact time. Wipe dry with a cloth, sponge or mop or allow to air dry. For heavily soiled areas, a preliminary cleaning is required. Spray 6 - 8 inches from the surface; rub with a brush, sponge or cloth. Do not breathe spray. Rinse all surfaces that come in contact with food such as countertops, appliances, tables and stovetops with potable water before reuse. Do not use on utensils, glassware and dishes. Bactericidal Stability of Use-Dilution: Tests confirmthat the use solution of this product, when stored in a sealed container such as a spray bottle, remains effective for up to 1 year. If product becomes visibly dirty or contaminated, the use-dilution must be discarded and fresh product prepared. Always use clean, properly labeled containers when diluting this product. For fungicidal activity: Betco Triforce is an effective fungicide against Trichophyton mentagrophytes [the athlete's foot fungus] when used on surfaces in areas such as locker rooms, dressing rooms, shower and bath areas and exercise facilities. Betco Triforce is a one-step fungicide at 1/2 oz. per gallon in 250 ppm hard water and 5% serum. For mold and mildew: At 1/2 oz. per gallon, Betco Triforce will effectively inhibit the growth of mold and mildew and the odors caused by them when applied to hard, nonporous surfaces. Follow disinfection instructions. Repeat treatment every seven days, or more often if new growth appears This product is not to be used as a terminal sterilant / high level disinfectant on any surface or instrument that (1) is introduced directly into the human body, either into or in contact with the bloodstream or normally sterile areas of the body, or (2) contacts intact mucous membranes but which does not ordinarily penetrate the blood barrier or otherwise enter normally sterile areas of the body.TO SANITIZE SOFT SURFACES:Add ½ oz. per gallon of water. Apply use-solution with a sprayer. Hold bottle 6" - 8" from surface and spray until fabric is wet. Fabric must remain wet for 5 minutes. Allow fabric to Air dry. Soiled areas must be cleaned prior to sanitizing.*KILLS HIV AND HBV AND HCV ON PRE-CLEANED ENVIRONMENTAL SURFACES / OBJECTS PREVIOUSLY SOILED WITH BLOOD / BODY FLUIDS in health care settings or other settings in which there is an expected likelihood of soiling of inanimate surfaces / objects with blood or body fluids, and in which the surfaces / objects likely to be soiled with blood or body fluids can be associated th the potential for transmission of Human Immunodeficiency Virus Type 1 [HIV-1] [associated with AIDS] or Hepatitis B Virus [HBV] or epatitis C Virus [HCV].Special Instructions for Cleaning and Decontamination against HIV-1 or HBV or HCV on Surfaces / Objects Soiled With Blood / Body Fluids. Personal Protection: Cleanup must always be done wearing protective gloves, gowns, masks and eye protection. Cleaning Procedure: Blood and other body fluids containing HIV-1 or HBV or HCV must be thoroughly cleaned from surfacesand objects before application of Betco Triforce.
For School, Restaurant, Food Handling and Processing Areas, Bar and Institutional Kitchen Use. This product kills 99.99% of Foodservice Germs E. coli, Salmonella, and Listeria. This product is an effective sanitizer at 200 ppm active quat for use on food contact surfaces in 500 ppm hard water against: Campylobacter jejuni, (Community Associated) Methicillin-Resistant Staphylococcus aureus, Escherichia coli, Escherichia coli 0157:H7, Klebsiella pneumoniae, Listeria monocytogenes, Salmonella enterica, Shigella sonneii, Staphylococcus aureus, Staphylococcus aureus Methicillin-Resistant - MRSA, Yersinia enterocolitica and Vibrio cholerae. DIRECTIONS FOR USE It is a violation of Federal Law to use this product in a manner inconsistent with its labeling. Disinfection Directions: Add 3 oz. of this product per 5 gallons of water to disinfect hard, nonporous surfaces. Before use in federally inspected meat and poultry food processing plants and dairies, food products and packaging materials must be removed from the room or carefully protected. When used on surfaces in areas such as locker rooms, dressing rooms, shower and bath areas and exercise facilities, this product is an effective fungicide against Trichophyton mentagrophytes the athlete's foot fungus. Apply use-solution with a cloth, mop, sponge, sprayer or by immersion, thoroughly wetting surfaces. For sprayer applications, use a coarse spray device. Spray 6 - 8 inches from surface; rub with brush, sponge or cloth. Do not breathe spray. Note: For spray applications, cover or remove all food products. Treated surfaces must remain wet for 10 minutes. Wipe dry with a clean cloth, sponge or mop or allow to air dry. Rinse food contact surfaces such as counter tops, tables, picnic tables, exteriors of appliances and / or stove tops with potable water prior to reuse. Do not use on glasses, dishes or utensils as a disinfectant. For heavily soiled areas, preclean first. Prepare a fresh solution daily or more often if the use solution becomes visibly diluted or soiled. For Use on Finished Floors: To limit gloss reduction use this product at 3 oz. per 5 gallons of water. Apply with a damp mop or autoscrubber. For use as a One-Step Cleaner and Disinfectant Against Bacteria and Viruses by Electrostatic Spraying: Electrostatic spray application is for efficacy claims with a 10 minute contact time and 450 ppm concentration. This application method is not to be used to treat hard, non-porous surfaces for sanitization or fungicidal claims. <ul> <li>Ensure bystanders and pets are not present in the room during application.</li> <li>Clean visibly dirty surfaces prior to spraying.</li> <li>Wear an N95 filtering facepiece respirator or half face respirator with a N95 filter and eye protection when spraying.</li> <li>Select a spray nozzle that produces spray droplet particles with a volume median diameter =80µm</li> <li>Place the electrostatic spray function in the ON position for electrostatic spray models that have the functionality to toggle ON/OFF.</li> <li>Hold the sprayer nozzle 1-2 feet away from the target surface. Starting at the highest point and working down to the lowest point, spray target surfaces using a smooth methodical "S" pattern. To avoid leaving gaps in sprayed surfaces, overlap previously treated surfaces when moving onto subsequent sections.</li> <li>The target surface must remain visibly wet for 10 minutes. Re-apply product as necessary to keep surface visibly wet for the duration of the contact time. Wipe surfaces dry or allow to air dry.</li> <li>Allow the treated room to remain unoccupied for 15 minutes before reentering.</li> </ul>
It is a violation of Federal law to use this product in a manner inconsistent with its labeling.DILUTION:(1:32) - 4 ounces per gallon of water (660 ppm quat) - 8 ounces per 2 gallons of water DISINFECTION / CLEANING / DEODORIZING DIRECTIONS: Remove heavy soil deposits from surface, then thoroughly wet surface with a use-solution of 4 ounces of the concentrate per gallon of water. Apply with a cloth, mop, sponge, or coarse spray or by soaking. For sprayer applications, use a coarse spray device. Spray 6 - 8 inches from the surface; rub with a brush, cloth or sponge. Do not breathe spray. Let solution remain on surface for a minimum of 10 minutes. Rinse or allow to air dry. Rinsing of floors is not necessary unless they are to be waxed or polished. Food contact surfaces must be thoroughly rinsed with potable water. This product must not be used to clean the following food contact surfaces: utensils, glassware and dishes. Prepare a fresh use-solution daily or more often if the solution becomes visibly dirty or diluted.TOILET BOWLS / URINALS: Swab bowl with brush to remove heavy soil prior to cleaning or disinfecting. Clean by applying diluted solution around the bowl and up under the rim. Stubborn stains may require brushing. To disinfect, first preclean to remove heavy soil, then remove or expel over the inner trap the residual bowl water. Pour in three ounces of the diluted solution. Swab the bowl completely using a scrub brush or mop, making sure to get under rim. Let stand for 10 minutes or overnight, then flush. FUNGICIDAL DIRECTIONS: For use in areas such as locker rooms, dressing rooms, shower and bath areas and exercise facilities follow disinfection directions. MILDEWSTATIC INSTRUCTIONS: Will effectively control the growth of mold and mildew, plus the odors caused by them when applied to hard, nonporous surfaces such as walls, floors and table tops. Apply use-solution of 4 ounces per gallon of water with a cloth, mop, sponge or coarse spray. Make sure to wet all surfaces completely. Let air dry. Repeat application weekly or when growth reappears. *KILLS HIV-1 (AIDS VIRUS) AND HBV (HEPATITIS B VIRUS) AND HCV (HEPATITIS C VIRUS) ON PRECLEANED, ENVIRONMENTAL SURFACES / OBJECTS PREVIOUSLY SOILED WITH BLOOD / BODY FLUIDS in settings in which there is an expected likelihood of soiling of inanimate surfaces/objects with blood / body fluids, and in which the surfaces / objects likely to be soiled with blood / body fluids can be associated with the potential for transmission of Human Immunodeficiency Virus Type I (HIV-1) (associated with AIDS) or Hepatitis B Virus (HBV) or Hepatitis C Virus (HCV). SPECIAL INSTRUCTIONS FOR CLEANING AND DECONTAMINATION AGAINST HIV-1 (AIDS VIRUS) OR HBV OR HCV OF SURFACES / OBJECTS SOILED WITH BLOOD / BODY FLUIDS: Personal Protection: Disposable protective gloves, gowns, face masks or eye coverings, as appropriate, must be worn during all cleaning of blood / body fluids and during decontamination procedures. Cleaning Procedures: Blood / body fluids must be thoroughly cleaned from surfaces / objects before application of disinfectant. Contact Time: HIV-1 (AIDS virus) is inactivated after a contact time of 4 minutes at 25°C (77°F) (room temperature). HBV and HCV are inactivated after a 10 minute contact time. Use a 10-minute contact time for all other viruses, fungi and bacteria listed. Disposal of Infectious Materials: Blood / body fluids should be autoclaved and disposed of according to federal, state and local regulations for infectious waste disposal. FARM PREMISE, LIVESTOCK, POULTRY & TURKEY HOUSE DISINFECTANT (DILUTION: 1:32; 4 ounces per gallon of w
Spray 6-8 inches from surface. Clean with a brush, sponge or cloth. Do not breathe spray. It is a violation of Federal Law to use this product in a manner inconsistent with its labeling.
This product can be used in multiple areas such as operating rooms, long-term care facilities, medical facilities, animal treatment facilities, cruise ships, hotels (motels), public buildings, public restrooms, recreational facilities, retail businesses and schools (colleges and universities)
<ul> <li>Add the product at ½ oz. per gallon of water (1:256).</li> <li>Pre-clean heavily soiled areas.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use solution to hard, non-porous environmental surfaces. To disinfect, all surfaces must remain wet for 10 minutes.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul> Note: Rinsing is not necessary unless floors are to be coated with finish or restorer. All food contact surfaces such as appliances and kitchen countertops must be rinsed with potable water. Do not use on glassware, utensils or dishes For Use as a Cleaner and Deodorizer <ul> <li>Apply use solution to hard, non-porous surfaces. Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary.</li> </ul> For Use as a Non-Acid Bowl Cleaner/Disinfectant in Toilet Bowls and Urinals from Use-Dilution Empty toilet bowls by forcing water through the trap. Apply use solution to exposed surfaces in toilet bowls and urinals. Swab entire surface area especially under rim. Allow entire surface to remain wet for 10 minutes. Flush toilet or urinal and rinse swab applicator thoroughly. For Use to Clean and Disinfect Shower Rooms, Locker Rooms and Other Large, Open Areas with Floor Drains <ul> <li>Apply use solution to floors, walls and ceilings. All surfaces must remain wet for 10 minutes. Scrub and rinse surfaces thoroughly and let air dry</li> </ul> To Kill Mold, Mildew and Fungi (in 5% soil load) <ul> <li>Apply use solution to hard, non-porous environmental surfaces and allow surfaces to remain wet for 10 minutes. Wipe and let air dry</li> </ul> To Control Mold and Mildew <ul> <li>Apply use solution to pre-cleaned hard, non-porous environmental surfaces and allow to air dry. Repeat weekly or when growth reappears</li> </ul>
<ul> <li>Hard surface cleaning and disinfection</li> <li>Designed for disinfecting medical hard, nonporous inanimate surfaces including: glass, glazed porcelain and stainless steel. Not recommended for use on: aluminum, brass, chipped enamel, clear plastic, copper, finished floors, natural marble, painted surfaces, and silver.</li> </ul>
<ul> <li>Spray surface until thoroughly wet. </li> <li>Allow surface to remain visibly wet. Read label for contact times. </li> <li>Wipe surface or let air dry.</li> </ul>
<ul> <li>Spray surfaces and let solution remain on surface for a minimum of 5 minutes</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted</li> </ul> Dilutable Disinfectant Cleaner <ul> <li>1:16 dilution - Virucidal, Bactericidal, and Fungicidal, including antibiotic resistant bacteria, in 5 minutes</li> <li>1:128 dilution - Non-food contact sanitizer in 3 minutes or general purpose cleaning</li> <li>1:256 dilution - Floor and general purpose cleaner</li> </ul> Note: Rinsing is not necessary unless floors are coated with finish or restorer.All food contact surfaces must be rinsed with potable water. Do not use on glassware, utensils or dishes. Prior to first use on a particular surface, it is recommended to test in a small, discreet area if there is concern of incompatibility, or contact a Diversey representative. Not recommended for floors at dilution 1:16. Refer to product label for complete use instructions.
<ul> <li>Use on hard, nonporous surfaces including vinyl, painted surfaces, plastic, glazed ceramic, glazed porcelain, chrome, laminated surfaces and bakes enamel surfaces</li> <li>Effective in health care, educational, lodging and food service environments</li> </ul>
DIRECTIONS FOR USE: It is a violation of Federal law to use this product in a manner inconsistent with its labeling. Before use in federally inspected meat and poultry food processing plants and dairies, food products and packaging materials must be removed from the room or carefully protected. DILUTION: [1:256] ½ oz. per gallon of water DISINFECTION/VIRUCIDAL*/FUNGICIDAL/MOLD AND MILDEW CONTROL DIRECTIONS: Apply use-solution to hard, nonporous surfaces, thoroughly wetting surfaces with a sprayer. Treated surfaces must remain wet for 3 minutes. For disinfection against Enterovirus. 5 minute contact time. For disinfection against Legionella pneumophilia, Staphylococcus aureus - Multi-Drug Resistant, and SARS Associated Coronavirus use 10 minute contact time. Wipe dry with a cloth, sponge or mop or allow to air dry. For heavily soiled areas, a preliminary cleaning is required. Spray 6 - 8 inches from the surface; rub with a brush, sponge or cloth. Do not breathe spray. Rinse all surfaces that come in contact with food such as countertops, appliances, tables and stovetops with potable water before reuse. Do not use on utensils, glassware and dishes. Bactericidal Stability of Use-Dilution: Tests confirmthat the use solution of this product, when stored in a sealed container such as a spray bottle, remains effective for up to 1 year. If product becomes visibly dirty or contaminated, the use-dilution must be discarded and fresh product prepared. Always use clean, properly labeled containers when diluting this product. For fungicidal activity: Betco Triforce is an effective fungicide against Trichophyton mentagrophytes [the athlete's foot fungus] when used on surfaces in areas such as locker rooms, dressing rooms, shower and bath areas and exercise facilities. Betco Triforce is a one-step fungicide at 1/2 oz. per gallon in 250 ppm hard water and 5% serum. For mold and mildew: At 1/2 oz. per gallon, Betco Triforce will effectively inhibit the growth of mold and mildew and the odors caused by them when applied to hard, nonporous surfaces. Follow disinfection instructions. Repeat treatment every seven days, or more often if new growth appears This product is not to be used as a terminal sterilant / high level disinfectant on any surface or instrument that (1) is introduced directly into the human body, either into or in contact with the bloodstream or normally sterile areas of the body, or (2) contacts intact mucous membranes but which does not ordinarily penetrate the blood barrier or otherwise enter normally sterile areas of the body.TO SANITIZE SOFT SURFACES:Add ½ oz. per gallon of water. Apply use-solution with a sprayer. Hold bottle 6" - 8" from surface and spray until fabric is wet. Fabric must remain wet for 5 minutes. Allow fabric to Air dry. Soiled areas must be cleaned prior to sanitizing.*KILLS HIV AND HBV AND HCV ON PRE-CLEANED ENVIRONMENTAL SURFACES / OBJECTS PREVIOUSLY SOILED WITH BLOOD / BODY FLUIDS in health care settings or other settings in which there is an expected likelihood of soiling of inanimate surfaces / objects with blood or body fluids, and in which the surfaces / objects likely to be soiled with blood or body fluids can be associated th the potential for transmission of Human Immunodeficiency Virus Type 1 [HIV-1] [associated with AIDS] or Hepatitis B Virus [HBV] or epatitis C Virus [HCV].Special Instructions for Cleaning and Decontamination against HIV-1 or HBV or HCV on Surfaces / Objects Soiled With Blood / Body Fluids. Personal Protection: Cleanup must always be done wearing protective gloves, gowns, masks and eye protection. Cleaning Procedure: Blood and other body fluids containing HIV-1 or HBV or HCV must be thoroughly cleaned from surfacesand objects before application of Betco Triforce.
SHAKE WELL BEFORE EACH USE. It is a violation of Federal law to use this product in a manner inconsistent with its labeling TO DISINFECT HARD, NON-POROUS SURFACES: Spray pre-cleaned surface until wet. Allow product to remain visibly wet on surface for 5 minutes. TO SANITIZE* HARD, NON-POROUS SURFACES: Spray pre-cleaned surface until wet. Allow product to remain visibly wet on surface for 30 seconds. TO INHIBIT THE GROWTH OF MOLD** AND MILDEW AND THEIR ODORS: Spray pre-cleaned surface until wet. Let the treated surface air dry. Re-apply as necessary STORAGE AND DISPOSAL STORAGE: Store away from heat, sparks and open flame, in an area inaccessible to children DISPOSAL: This container may be recycled in the few but growing number of communities where aerosol can recycling is available. Before oering for recycling, empty the can by using the product according to the label. DO NOT PUNCTURE! If recycling is not available, wrap the container and discard in trash. PRECAUTIONARY STATEMENTS HAZARDS TO HUMANS AND DOMESTIC ANIMALS. CAUTION: Causes moderate eye irritation. Avoid contact with eyes or clothing. Wash thoroughly with soap and water after handling and before eating, drinking, chewing gum or using tobacco. Avoid contact with food and food utensils. Before using product throughout your home, use in one room and wait 24 hours to ensure that no one has any physical reactions to the product Asthma and Allergy Suerers: Consult your physician before using this product in your home. Before spraying remove birds. After use, ventilate normally prior to returning birds to treated area. FIRST AID: IF IN EYES: Hold eye open and rinse slowly and gently with water for 15-20 minutes. Remove contact lenses, if present, after the first 5 minutes, then continue rinsing eye. Call a poison control center or doctor for treatment advice. Have the product container or label with you when calling a poison control center or doctor, or going for treatment.
Virex® Plus is a one-step, quaternary-based disinfectant cleaner concentrate for use on hard, nonporous surfaces such as floors, walls, glazed porcelain, and plastic surfaces in hospitals, nursing homes, schools, hotels, public areas and other facilities where cleaning and prevention of cross-contamination are critical. Preparation of Disinfectant Use-Solution <ul> <li>Mix ½ oz. per gallon of water (1:256). Use 1 oz. per gallon of water to kill Norovirus , Enterobacter aerogenes, and Serratia marcescens. Use 2 oz. per gallon of water to kill Adenovirus Type 5 and Type 7.</li> </ul> For Use as a One-Step Cleaner/Disinfectant <ul> <li>Apply use-solution with a sprayer, thoroughly wetting surface.</li> <li>Let treated surface remain wet for contact time indicated on label or reference sheet.</li> <li>Wipe dry with a cloth, sponge, or mop, or allow to air dry.</li> <li>Prepare a fresh solution if the solution becomes visibly dirty or diluted.</li> </ul> For Use as a Cleaner and Deodorizer <ul> <li>Apply use-solution using a sprayer.</li> <li>Air Dry, wipe surfaces to dry and remove any residue, or rinse with potable water as necessary</li> </ul>