Container Type
Bag
Bottle

Dilution System
Yes

Directions/Instructions
Use Instructions <ul> <li>Blockade areas to be stripped or finished. Floors will be very slippery until dry.</li> <li>Strip floors, using a Diversey stripper per the instructions on the stripper label</li> </ul> Coating <ul> <li>Apply 3 or more medium coats using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Apply additional coats until desired gloss is obtained.</li> <li>Allow 30-45 minutes drying time between coats. Temperature, humidity and ventilation may affect drying time. Allow finish to cure for 24 hours before burnishing.</li> </ul> Maintenance <ul> <li>Dust mop or sweep. Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions.</li> <li>If desired, dry buff using medium to aggressive pad and 1000- 500 rpm equipment. Ultra-high speed burnish using a medium aggressiveness pad and 2000+ rpm equipment.</li> </ul> Recoating <ul> <li>Dust mop or sweep Clean the floor with a mop or an automatic scrubber using the recommended Diversey brand cleaner according to label directions</li> <li>Blockade area and apply 1-2 uniform coats of finish using a clean finish mop or the Diversey ProSpeedTM/MC or TrailBlazerTM/MC Floor Finish Applicator System. Allow finish to cure for 24 hours before burnishing.</li> </ul> Removal <ul> <li>Remove using recommended Diversey brand stripper following label directions</li> </ul> Precautions <ul> <li>Do not dilute. Do not use on surfaces colder than 50°F (10°C) @ 15% RH. To avoid contamination, do not return unused finish to original container. Do not freeze.</li> </ul>
Use Instructions <ul> <li>Blockade areas to be stripped. Floors will become very slippery when stripper is applied. Exercise caution.</li> <li>Gloves, goggles and protective footwear is recommended when using this product</li> <li>Dilute or dispense using cold water</li> <li>Apply liberal amounts of stripper solution uniformly to floor with mop. Start at edges to provide more soak time. If splashing occurs, wipe off surfaces with a clean, damp rag.</li> <li>Let stripper solution soak 10-15 minutes. Mop agitate to loosen finish. Re-wet as necessary. Do not allow solution to dry on floor. Longer soak times may be necessary in cases of extreme buildup.</li> <li>Hand or machine scrub thoroughly using appropriate stripper pads or stripping brush. Pick up all solution with a clean mop, wet vac, or automatic scrubber. Mop up any 'tracks' left by wet vacs or scrubbers before they dry.</li> <li>Thoroughly rinse floor with clean water, using a mop and bucket. Let floor dry completely before applying a Diversey Green Seal®-Certified finish or other recommended Diversey brand floor finish or sealer.</li> </ul>
Use Instructions <ul> <li>Use appropriate personal protective equipment</li> </ul> Dilute product as follows: <ul> <li>Light Build-up of Floor Finishes: Dilute product between 1:8 (16 fl. oz. / gal.) and 1:10 (13 fl. oz. / gal.) with cool water</li> <li>Heavy Build-up of Floor Finishes: Dilute product between 1:4 (32 fl. oz. / gal.) and 1:6 (24 fl. oz. / gal.) with cool water</li> <li>Heavy Build-up of Concrete Sealers: Dilute product at 1:2 (64 fl. oz. / gal.) with cool water</li> <li>Blockade areas to be stripped. Floors will be very slippery when stripper is applied. Exercise caution.</li> <li>Apply liberal amounts of solution uniformly to floor with a mop. Start with the edges to give them more soak time. If splashing occurs, wipe off surfaces with a clean rag dampened with water.</li> <li>Let stripper solution soak for 10-15 minutes. Mop agitate to loosen finish or sealer. Re-wet as necessary, do not allow stripper to dry on the floor. Longer soak times may be necessary in cases of extreme buildup.</li> <li>Hand or machine scrub thoroughly using appropriate stripper pads or stripping brush</li> <li>Pick-up all of the solution with a clean mop, wet vac or automatic scrubber</li> <li>Mop up any "tracks" left by wet vacs or automatic scrubbers before they dry. Thoroughly rinse floor with clean water, using a mop and bucket.</li> <li>Let floor dry completely before applying recommended Diversey brand floor sealer or finish</li> </ul> Important: <ul> <li>Do not use on wood, linoleum, rubber, marble, painted surfaces, on surface colored and acid dyed concrete floors as this product may harm these surfaces. Test for softening or color bleeding on asphalt floors before using.</li> </ul>
Directions for UseRecommended for use on all types of resilient tile flooring and properly prepared hard surfaces.RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco&#174; stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance.ROUTINE MAINTENANCE:Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco&#174; One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating.INTERIM MAINTENANCE:Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above.Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum
For Prespray Cleaning <ul> <li>Thoroughly vacuum carpet and pre treat spots.</li> <li>Dilute 10 oz. Heavy Duty Prespray with 1 gallon hot water (1 L with 12 L) in pump-up sprayer or fill directly from J-Fill® dispenser.</li> <li>Spray carpet completely, paying particular attention to traffic lanes and spots.</li> <li>Agitate with a carpet rake, extractor brush, shampoo brush or bonnet.</li> <li>Allow 5-10 minutes for Heavy Duty Prespray to completely loosen soils.</li> <li>Thoroughly extract carpet with Extraction Rinse according to use directions. Use Liquid Defoamer in recovery tank if required.</li> </ul> For Bonnet Cleaning <ul> <li>Dilute at 1:32 or 4 oz./gal. (35 mL per L) with warm water.</li> <li>Apply light mist onto carpet bonnet.</li> <li>Bonnet buff carpet with your pad. Flip pad when soiled. When both sides are soiled, rinse or launder.</li> <li>e This solution can also be used for spot treatment. Treat spot, agitate and rinse thoroughly.</li> </ul>
For Use on Floors: <ul> <li>Dilute ¼ cup Murphy Oil Soap in 1 gallon of warm water</li> <li>For heavy cleaning dilute ½ cup Murphy Oil Soap per gallon </li> <li>Clean with well wrung-out mop, and mop any excess water</li> <li>No rinsing required.</li> </ul> Other Surfaces: Wet cloth with diluted Murphy Oil Soap liquid. Wipe clean to reveal wood's natural beauty
Pro-Tip: For use as in facilities with black asphalt type flooring, such as U.S. Postal Facilities.
Pro-Tip: Use for ordinary scrubbing of floor by hand or for automatic floor-scrubbing machines. Also used on walls, tables and all other hard surfaces.
Drop one PAC into a bucket filled with 1.6 gallons of warm water. After the satisfying fizz subsides, you're ready to mop. Simply mop all your hard surface floors as you normally would and enjoy the streak-free results. Not intended for use with spray mops. Keep out of the reach of children.
Recommended for mopping or autoscrubbing finished floors. Can also be used as a spray and wipe cleaner on appliances, desks, plastic, stainless steel and painted surfaces. 1. Dilute 1 to 3 U.S. oz./U.S. gal. or 8 to 23 mL/L of water, depending on soil conditions.2. Apply cleaning solution using a mop or autoscrubber.3. Pick up the solution. Rinsing is not required except in very dirty situations.4. Allow floor to dry thoroughly.
Recommended for polished concrete and terrazzo surfaces for extended stain and etch protection. Clean entire area with Betco DensiClean, allow floor to dry prior to application. Apply Betco LiquiShield at proper application rate, 3,000 to 4,000 sq. ft. per gal, with a low-pressure sprayer spread with a microfiber applicator pad or mop and bucket application. Allow to dry to touch, 45 to 60 minutes, then apply second coat using the same procedures. Allow second coat to dry 60 minnutes then high speed burnish with Betco Si Burnish Pad. Allow 1 to 2 hours cure time before floor is exposed to full traffic. Allow 24 hours before the use of cleaners on the floor. Maintain floor with Betco Crete Rx DensiClean and Betco Crete Rx Cleaning Pads for maximum protection and shine.
Recommended for top scrubbing all types of water-based acrylic floor finishes and sealers on all types of resilient tile (vinyl composition, vinyl and linoleum). To be used as a top scrub cleaner in preparing a coated floor surface for recoating. Dilute Best Scrub 8 1/2 oz./gal. or 65 mL/L (1:15). Apply solution to floor using a mop or automatic scrubber. Agitate solution using a green cleaning pad or brush. Remove solution from the floor with a mop, wet vacuum, or automatic scrubber. When removed properly no flood rinsing is required. After the floor has dried check for residue. If any residue is present a rinse will be needed. If initial scrubbing does not remove embedded dirt, the floor may need additional scrubbing or may require stripping.
Recommended for top scrubbing all types of water-based acrylic floor finishes and sealers on all types of resilient tile (vinyl composition, vinyl and linoleum). To be used as a top scrub cleaner in preparing a coated floor surface for recoating. Dilute Best Scrub 8 1/2 oz./gal. or 65 mL/L (1:15). Apply solution to floor using a mop or automatic scrubber. Agitate solution using a green cleaning pad or brush. Remove solution from the floor with a mop, wet vacuum, or automatic scrubber. When removed properly no flood rinsing is required. After the floor has dried check for residue. If any residue is present a rinse will be needed. If initial scrubbing does not remove embedded dirt, the floor may need additional scrubbing or may require stripping.
Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco® stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance. ROUTINE MAINTENANCE: Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco® One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating. INTERIM MAINTENANCE: Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.
Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco® stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply floor finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance. ROUTINE MAINTENANCE: Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco® One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating. INTERIM MAINTENANCE: Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.
Recommended for use on all types of stone flooring (brick, marble, slate, terrazzo and concrete-new and old), resilient tile, quarry and non-glazed ceramic tile. RESTORATIVE MAINTENANCE:Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 30 - 45 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. ROUTINE MAINTENANCE:Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating. INTERIM MAINTENANCE:Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. Please recycle empty containers. CONCRETE APPLICATION:May be applied to new concrete after 30 days (fully cured) and a surface temperature above 50 °F. Prior to applying sealer to new concrete, use an acidic solution to neutralize excess alkalinity. All new concrete must be cleaned and rinsed. Not for use outdoors. Old concrete must be cleaned with a degreasing solution and rinsed for proper adhesion. GLAZED TILE/POLISHED SURFACES:1. Test in an inconspicuous area first, proper adhesion may be difficult due to lack of porosity. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.
Recommended for use with steam and hot water extractors on all types of carpeting (including Stain Resistant), upholstery and rugs. Please recycle empty containers.1. Vacuum carpet.2. Dilute 0.5 oz./gal. or 3.9 mL/L (1:256) of water. If carpet is heavily soiled, 1 oz./gal. or 7.8 mL/L (1:128) of water. Cleaning solution may also be used as a prespray, sprayed directly onto the carpeting.3. Follow operating instructions on extraction equipment.4. Allow the carpet to dry thoroughly before allowing traffic.
Remove soil and dust mop the floor. Spray a light mist of product on the floor in front of the floor machine. DO NOT OVERWET. Using a nylon or polyester spray buff pad, buff the floor where the fine mist of spray buff has been applied. Flip or change pad as necessary. After spray buffing the floor is completed, dust mop the floor if dust is still present. NOTE: In order for spray buff to work correctly, three or four base coats of floor finish must be applied before using spray buff in order to achieve maximum gloss and wear properties. Heavy traffic areas may require dust mopping, followed by damp mopping, followed by spray buffing. Use of this spray buff will eliminate powdering and will never yellow the floor. NOTE: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.
<ul> <li>A highly effective cleaner designed to remove soils and oils without dulling or altering the appearance of your floor</li> <li>Designed for use on most floor types</li> <li>Part of a comprehensive floor care offering for cleaning, maintaining, stripping and finishing floors</li> </ul>
<ul> <li>Wear safety glasses & gloves </li> <li>Dust mop or sweep area</li> <li>Use 2 oz of product per 1 gallon of water</li> <li>Wring mop until damp</li> <li>Mop onto surface in a pattern and allow to air dry</li> </ul>
<ul><li> For use as a powerful rinse aid</li><li> Safe to use on all colorfast carpets</li></ul>
<ul><li> Recommended ESIor removing water-based acrylic floor finishes from all types of resilient tile and hard surfaces. Pre-test in a small area; color bleeding or discoloration may occur on linoleum, rubber tile or asphalt tile.</li><li> Not recommended for stripping linoleum or sheet vinyl floors.</li><li> Sweep or dust mop the floor to remove any large debris. Dilute with warm to hot water.</li><li> For normal stripping, dilute 13 oz./gal. or 100 mL/L (1:10) of water.</li><li> For heavy stripping, dilute 25 oz./gal. or 200 mL/L (1:5) of water.</li><li> Apply solution liberally to floor surface. Allow a minimum of 5 minutes contact time. Be sure to keep surface wet at all times. Agitate with a low-speed rotary machine, automatic scrubber or stripping machine. Pick up the solution with a wet vacuum, an automatic scrubber or a mop and bucket and thoroughly rinse the floor. Allow floor to dry completely before applying finish or sealer. No flood rinsing is necessary if surface appears free of dust and residue. Please recycle empty container.</li></ul>
<ul><li> Recommended for removing multiple coats of water-based acrylic and urethane fortified floor finishes from all types of resilient tile and hard surfaces. Not Recommended on linoleum or sheet vinyl floors. Pre-test in a small area; bleeding or discoloration may our on linoleum, rubber tile, or asphalt tile. Sweep or dust mop floors or to remove any large debris. </li><li> For light to medium strip, dilute 10 oz. /gal. (1:12). </li><li> For heavy striping, dilute 25 oz. /gal. (1:5) with cold water. </li><li> Apply solution liberally to floor surface. Allow 3-5 minutes contact time. Be sure to keep surface wet at all times. Agitate with a low speed rotary machine, automatic scrubber or stripping machine. Pick up solution with a wet vacuum, automatic scrubber or mop and bucket and thoroughly rinse the floor. Allow floors or to dry completely before applying finish or sealer. No flood rinsing is necessary if surface appears free of dust and residue.</li></ul>
<ul><li> Responds beautifully to conventional, high-speed or UHS equipment and maintenance procedures</li><li> May require a sealer on highly polished stone, glazed clay tile, and some rubber floors</li><li> Not intended for use on cork, wood, or bamboo flooring unless specified by the manufacturer</li></ul>
<ul><li> Use as a daily floor cleaner on most floor types</li><li> Can also be used as a high performance general purpose cleaner</li></ul>
If being used on a carpet for the first time test for colorfastness on an inconspicuous area. Remove gross soil. Extract using Extraction Rinse. Dilute product 1 to 4 oz. per gallon (30 to 120 mL/3.78 L). Saturate the spot/stain and surrounding area. Agitate. Place towel moistened with product over treated area for 24 hours. Remove towel and repeat treatment as necessary. Extract with Extraction Rinse. Allow carpet to dry. Use also as a drain cleaner and odor counteractant cleaner in restrooms; or bonnet buff using the dilutions outlined above.directions.
Recommended for mopping or autoscrubbing finished floors. Can also be used as a spray and wipe cleaner on appliances, desks, plastic, stainless steel and painted surfaces. <ul> <li>Dilute 0.5 US oz./US gal. or 4 mL /L of water, depending on soil conditions.</li> <li>Apply cleaning solution using a mop or autoscrubber.</li> <li>Pick up the solution. Rinsing is not required except in very dirty situations .</li> <li>Allow floor to dry thoroughly.</li> </ul>
Recommended for removing multiple coats of water-based acrylic floor finishes from all types of resilient tile and hard surfaces. Not recommended on linoleum or sheet vinyl floors. Pre-test in a small area; color bleeding or discoloration may occur on linoleum, rubber tile, or asphalt tile. Sweep or dust mop floor to remove any large debris. For light to medium stripping, dilute 10 oz. /gal. (1:12). For heavy stripping, dilute 25 oz. /gal. (1:5) with cool water. Apply solution liberally to floor surface. Allow 3 - 5 minutes contact time. Be sure to keep surface wet at all times. Agitate with a low speed rotary machine, automatic scrubber or stripping machine. Pick up solution with a wet vacuum, automatic scrubber or mop and bucket and thoroughly rinse the floor. Allow floor to dry completely before applying finish or sealer. No flood rinsing is necessary if surface appears free of dust and residue.
Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco® stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance. ROUTINE MAINTENANCE: Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco® One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating. INTERIM MAINTENANCE: Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.
Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply finish in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 4 coats of finish is recommended. Note: This product is a self-sealing finish, however, if tile is old, worn or porous, initially applying 1 - 2 coats of a Betco sealer will enhance gloss and long term performance. ROUTINE MAINTENANCE: Sweep large debris and dust mop. Damp mop or automatic scrub using a Betco floor cleaner. Buff or burnish the floor to enhance gloss as needed. Use Betco One Step High Speed Cleaner/Restorer to condition the floor and extend the time between top scrub and recoating. INTERIM MAINTENANCE: Sweep large debris and dust mop. Top scrub the floor using Daily Scrub SC and maroon pad or equivalent to remove the top soiled layers of finish. Floor surface must be clean, dry and free of residue before finish is applied. Apply 1 - 2 coats of finish as directed above. Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.
Recommended for use on all types of resilient tile flooring and properly prepared hard surfaces. This product is of specific benefit in preparing old, worn or porous tile floors for finishing. RESTORATIVE MAINTENANCE: Completely remove all old wax, finish and soil from floor surface following strip procedure instructions on Betco® stripper label. Floor surface must be clean, dry and free of residue before finish is applied. Rinse with clean water if necessary. Apply sealer in uniform, thin to medium coats using a clean synthetic finish mop, microfiber mop or applicator system. Allow each coat to dry thoroughly before applying additional coats, usually 20 - 30 minutes. Elevated temperatures, heavy coats and humidity may extend dry time. A minimum of 2 coats of sealer is recommended. This sealer can be used as a finish coat, however, for a better shine, increased protection and easier maintenance, we recommended the application of 2 - 4 coats of a Betco floor finish that best fits your maintenance program. Please recycle empty containers. Note: Slip resistance meets or exceeds standard, (ASTM D 2047-11) James Machine 0.5 minimum.

Kill Claims
Severe Acute Respiratory Syndrome Coronavirus (SARS-CoV)

Non-Acidic
Yes

Product Material
MicroFiber

Quantity Per Container
Bottle

Popular tags

Luxe

Floor & Carpet Cleaners

View as Grid List

Sort by

Display per page

Diversey Profi Floor Cleaner/Grease Remover

DVO94512759

Liquid - 128 fl oz (4 quart) - Surfactant Scent - 4 / Carton - White

$271.71 $207.34

Betco Ax-It Plus No-Rinse Stripper

BET154B500

Concentrate - 640 fl oz (20 quart) - 1 Each - Low Foaming, Rinse-free, Fast Acting, Versatile, Pleasant Scent, Residue-free - Clear, Amber

$122.78 $121.78

Diversey Floor Cleaner/Maintainer

DVO92974600

Liquid - 32 fl oz (1 quart) - Sweet Scent - 6 / Carton - Red

$273.05 $203.01

Diversey High Mileage Floor Finish

DVO95109638

Ready-To-Use Liquid - 84.5 fl oz (2.6 quart) - Solvent Scent - 6 / Carton - White

$289.07 $192.65

Diversey Stench & Stain Digester

DVO904271

Liquid - 32 fl oz (1 quart) - Floral Scent - 6 / Carton - Tan

$269.12 $189.27

Diversey Carefree Floor Finish/Sealer

DVO5104731

Ready-To-Use - 640 fl oz (20 quart) - Ammonia Scent - 1 Each - Versatile, Easy to Use, Durable, Slip Resistant - Off White

$235.45

Betco BioActive Solutions Floor Cleaner

BET2580400

Ready-To-Use Liquid - 144.80 oz (9.05 lb) - Rain Fresh Scent - 4 Case - Light Green, Green

$108.45 $108.44

Betco Acrylic Polymer Floor Sealer

BET6070400CT

Liquid - 128 fl oz (4 quart) - Characteristic ScentBottle - 4 / Carton - Clear, Milky White

$135.92 $110.04

Diversey Vectra Floor Finish

DVO5105047

Ready-To-Use Liquid - 640 fl oz (20 quart) - Ammonia Scent - 1 Each - Off White

$257.26 $182.17

Diversey Floor Cleaner/Maintainer

DVO904636

Liquid - 640 fl oz (20 quart) - Sweet Scent - 1 Each - Pink

$251.24 $181.78

Diversey Pro Strip SC High Efficiency Floor Stripper

DVO95547355

Concentrate Liquid - 84.5 fl oz (2.6 quart) - Solvent ScentBottle - 2 / Carton - Amber

$261.75 $179.32

Zep Commercial SHIELD Floor Polish

ZPE197135

For Floor, Multipurpose - 640 fl oz (20 quart) - 1 Each - Water Based, Durable, Scuff Resistant, Black Mark Resistant, Slip Resistant - Milky White

$215.61 $178.45

Diversey Speedtrack Clean/Burnish Maintainer

DVO94033110

Liquid - 128 fl oz (4 quart) - 4 / Carton - White

$232.14 $172.13

Zep Commercial Black Out Floor Polish

ZPE184335

640 fl oz (20 quart) - Mild Scent - 1 Carton - Slip Resistant, Quick Drying - Milky White

$262.13 $167.77

Betco FiberPRO Extraction Cleaner

BET4120400

For Carpet, Upholstery, Rug - Concentrate - Liquid - 128 fl oz (4 quart) - 9.5 to 10.5 pH - Pleasant Scent - Low Foaming, Stain Resistant - Green Bottle - 4 / Carton

$136.49 $98.20

Diversey Snapback UHS Restorer

DVO4134

Liquid - 128 fl oz (4 quart) - Lemon Scent - 4 / Carton - Blue

$268.88 $164.20

Diversey Pro Strip Heavy Duty Floor Stripper

DVO95032360

Liquid - 640 fl oz (20 quart) - Cherry Almond Scent - 1 / Carton - Straw

$247.42 $162.01

Diversey Dry Foam Shampoo & Cleaner

DVO9BP92017

Liquid - 128 fl oz (4 quart) - Floral Scent - 4 / Carton - Straw

$224.40 $158.90

Floor & Carpet Cleaners

Diversey Profi Floor Cleaner/Grease Remover

Betco Ax-It Plus No-Rinse Stripper

Diversey Floor Cleaner/Maintainer

Diversey High Mileage Floor Finish

Diversey Stench & Stain Digester

Diversey Carefree Floor Finish/Sealer

Betco BioActive Solutions Floor Cleaner

Betco Acrylic Polymer Floor Sealer

Diversey Vectra Floor Finish

Diversey Floor Cleaner/Maintainer

Diversey Pro Strip SC High Efficiency Floor Stripper

Zep Commercial SHIELD Floor Polish

Diversey Speedtrack Clean/Burnish Maintainer

Zep Commercial Black Out Floor Polish

Betco FiberPRO Extraction Cleaner

Diversey Snapback UHS Restorer

Diversey Pro Strip Heavy Duty Floor Stripper

Diversey Dry Foam Shampoo & Cleaner

Useful Links

Contact Us